Search

Categories

Downloads

Information

100% secure shopping!
Your data are safe with us. SSL-Protected!

E/PS 9000-2U Laboratory Power Supply 1000-3000 W

EPS9000_2U_TFT display The electronic high performance power supplies of the »E/PS 9000 2U« of EPS Electronic Power Supplies series are especially suitable for test systems and industrial controls due to their compact construction in a 19" enclosure with 2 height units (2U).
DC output voltages between 0-40V (SELV) and 0-750V, output currents between 0-4A and 0-120A and output power ratings of 0- 1000/1500/3000W are available.

Actual values, set values, status and alarms are clearly represented on the coloured TFT display.
For remote control using a PC or PLC the devices are provided as standard with an Ethernet and USB-B slot on the rear side as well as a galvanically isolated analog interface.

In addtion, the devices offer as standard the parallel switching in Shared Bus operation for constant current sharing. Operating in this way allows up to 10 units to be combined to a single system with a total power of up to 30kW per 42U rack. Also you have the possibility to connect the compatible power supplies via a Shared Bus, in order to create a so-called two-quadrant system. Typical applications i.e. for the source-sink principle are: battery test with automatic charge and discharge cycles, automotive electronic tests with simulation of transients (like voltage break-ins during engine starts) and cyclic charging and discharging of capacitors. A series operation is also possible with max. potential shift of 400V against PE on any DC minus pole.

All models are controlled by microprozessors. These enable an exact and fast measurement and display of actual values.
With the lock push button the controls can be locked, in order to protect the equipment from unintentional misuse.

In order to achieve rapid voltage changes with minimal ramp up and down times, the filter capacity can be reduced with the option High speed »EPS/HS«. It results in ramp times in the range of microseconds.
Models with a nominal output voltage of 200V or higher include a discharge circuit for the output capacities. For no load or low load situations, it ensures that the dangerous output voltage can sink to under 60V DC in max. 10 seconds after the DC output has been switched off (SELV according to EN60950).

Further options are GPIB and calibration with protocol.

Energy efficiency: Auto-ranging, high efficiency, temperature controlled fans

Scope of delivery:
Power Supply Unit
Test report
Mains cord Euro,UK and/or Swiss
plug (depending on destination)
Share bus plug
Remote Sensing plug
USB cable 1,8m
USB-Stick with manual and Software


E/PS 9080-40 2U Laboratory Power Supply

E/PS 9080-40 2U Laboratory Power Supply
Order Code: 102601

Voltage:  0-80 VDC
Current:  0-40 A
Output Power:  0-1000 W
Design:  19 inch

Productdetails

Output Voltage: 0 VDC - 80 VDC
Output Current: 0 A - 40 A
Output Power: 0-1000 W
Input Voltage: 90-264 VAC, 1 ph.+N; 50/60 Hz
Dimensions (WxHxD): 19"x2Ux463mm
Protection: OVP, OCP, OPP and OTP
Constant Voltage- (CV) Current (CC) and Power (CP)
Remote sensing (auto-sensing)
Series and Parallel operation
Preset of 5 different output values
Analog Interface, isolated
Ethernet and USB Interface with LabView VIs

Country of origin: Germany
Customs tariff code: 8504.3121

Accessories


More images


E/PS 9200-15 2U Laboratory Power Supply

E/PS 9200-15 2U Laboratory Power Supply
Order Code: 102602

Voltage:  0-200 VDC
Current:  0-15 A
Output Power:  0-1000 W
Design:  19 inch

Productdetails

Output Voltage: 0 VDC - 200 VDC
Output Current: 0 A -15 A
Output Power: 0-1000 W
Input Voltage: 90-264 VAC, 1ph.+N; 50/60 Hz
Dimensions (WxHxD): 19"x2Ux463mm
Protection: OVP, OCP, OPP and OTP
Constant Voltage- (CV) Current (CC) and Power (CP)
Remote sensing (auto-sensing)
Series and Parallel operation
Preset of 5 different output values
Analog Interface, isolated
Ethernet and USB Interface with LabView VIs

Country of origin: Germany
Customs tariff code: 8504.3121

Accessories


More images


E/PS 9360-10 2U Laboratory Power Supply

E/PS 9360-10 2U Laboratory Power Supply
Order Code: 102603

Voltage:  0-360 VDC
Current:  0-10 A
Output Power:  0-1000 W
Design:  19 inch

Productdetails

Output Voltage: 0 VDC - 360 VDC
Output Current: 0 A -10 A
Output Power: 0-1000 W
Input Voltage: 90-264 VAC, 1ph.+N; 50/60 Hz
Dimensions (WxHxD): 19"x2Ux463mm
Protection: OVP, OCP, OPP and OTP
Constant Voltage- (CV) Current (CC) and Power (CP)
Remote sensing (auto-sensing)
Parallel operation
Preset of 5 different output values
Analog Interface, isolated
Ethernet and USB Interface with LabView VIs

Country of origin: Germany
Customs tariff code: 8504.3121

Accessories


More images


E/PS 9500-06 2U Laboratory Power Supply

E/PS 9500-06 2U Laboratory Power Supply
Order Code: 102604

Voltage:  0-500 VDC
Current:  0-6 A
Output Power:  0-1000 W
Design:  19 inch

Productdetails

Output Voltage: 0 VDC - 500 VDC
Output Current: 0 A -06 A
Output Power: 0-1000 W
Input Voltage: 90-264 VAC, 1ph.+N; 50/60 Hz
Dimensions (WxHxD): 19"x2Ux463mm
Protection: OVP, OCP, OPP and OTP
Constant Voltage- (CV) Current (CC) and Power (CP)
Remote sensing (auto-sensing)
Parallel operation
Preset of 5 different output values
Analog Interface, isolated
Ethernet and USB Interface with LabView VIs

Country of origin: Germany
Customs tariff code: 8504.3121

Accessories


More images


Show 1 to 4 (of in total 18 products) Sites:  1  2  3  4  5  [next >>] 
You receive an overview to our services and products in our catalogue. Request today your copy by phone +49-(0)821-570451-0. Alternatively you can download even now our catalogue as pdf document on your PC or equivalent browse it at the screen.
⇏ Actual EPS-catalogue (PDF)